ISO 15848 Valve Fugitive Emissions: Buyer’s RFQ Guide

Specify ISO 15848 fugitive-emissions requirements for valves. Distinguish type qualification from production acceptance and define RFQ evidence.

ZHONGYUE VALVE

11/15/20263 min read

Pneumatic diaphragm control valve product image from Zhongyue Valve
Pneumatic diaphragm control valve product image from Zhongyue Valve

Fugitive-emissions requirements control external leakage from valve stem or shaft seals and body joints. They are not the same as seat leakage requirements. A clear RFQ must state which ISO 15848 part applies, the required qualification or production acceptance, and the evidence that must accompany the offered valve.

ISO 15848-1 addresses type testing and classification of valves for fugitive emissions. ISO 15848-2 addresses production acceptance testing. Using only the phrase “ISO 15848 valve” leaves important commercial and technical questions unanswered.

Separate External Leakage from Seat Leakage

External leakage can occur through dynamic stem or shaft packing and through static body, bonnet or cover joints. ISO 15848 evaluates these external emission paths under defined test conditions.

Seat leakage is internal leakage across the closed obturator. It is normally specified under a valve pressure-test standard or a control-valve seat leakage classification. A valve can meet a seat leakage requirement without meeting a fugitive-emissions class, and the reverse is also possible.

The RFQ should therefore list external fugitive-emissions requirements and seat leakage requirements as separate lines, each with its own standard and acceptance criteria.

Define Type Qualification Under ISO 15848-1

When ISO 15848-1 qualification is required, the purchaser should define the required classification and service envelope from the project specification. Relevant parameters include the test fluid, leakage class, temperature class, endurance class, number of mechanical cycles, number of thermal cycles and stem-seal adjustment conditions.

Do not invent a classification after quotation. The required class affects packing selection, stem finish, gland arrangement, body-joint sealing and the qualification evidence needed.

  • Tested valve type and construction;

  • size and pressure class;

  • stem or shaft diameter and surface condition;

  • packing material, number of rings and gland arrangement;

  • body-joint gasket or seal design;

  • body, bonnet, stem and sealing materials;

  • test temperature and pressure;

  • mechanical and thermal cycling;

  • measured leakage and final classification;

  • laboratory, report number, date, range and limitations.

The offered valve should be compared with the qualified design. A report for a different packing system or body-joint arrangement may not establish coverage.

Specify Production Acceptance Under ISO 15848-2

ISO 15848-2 provides a production acceptance test for industrial valves. It should not be confused with the longer type-qualification program in Part 1.

The purchase order should state whether production acceptance is required for every valve or according to an approved sampling plan. It should also define the test medium, pressure, measurement method, acceptance criteria, reporting format and witness requirements.

Production testing needs to be coordinated with the manufacturing schedule and ITP. If a third-party inspector will witness the test, identify the notification period and document review point before production starts.

Include the Actuated Assembly and Maintenance Conditions

An actuator can affect access to the packing gland, stem loading and the ability to make permitted adjustments. For control valves and automated on-off valves, provide the actuator type, fail position, travel, cycling duty and mounting arrangement.

Also clarify whether packing adjustment is permitted during qualification or acceptance testing and how the final gland setting is recorded. For service, request installation and maintenance instructions covering packing inspection, adjustment limits and replacement parts.

Fugitive-emissions performance depends on the complete sealing system and assembly condition. It should not be inferred from the packing material name alone.

ISO 15848 Valve RFQ Checklist

  1. Valve type, size, pressure class and end connection.

  2. Process fluid, pressure and temperature envelope.

  3. ISO 15848-1 type-qualification class and edition, if required.

  4. ISO 15848-2 production acceptance scope, if required.

  5. Stem or shaft, packing, gland and body-joint construction.

  6. Actuator, cycling duty and fail position.

  7. Separate seat leakage standard and acceptance class.

  8. Certificate, test report and qualification-range evidence.

  9. Production sampling, witness and reporting requirements.

  10. Supplier deviations and recommended spare packing.

For an automated regulating-valve inquiry, review Zhongyue Valve’s pneumatic diaphragm control valve page and submit the operating data through the contact page. The public product photograph shows a valve configuration only; it does not establish an ISO 15848 class or test status.

Zhongyue High Quality Valve Manufacturer

The products are exported to the United States, Europe, the Middle East, Southeast Asia, Russia and other countries and regions, reliable quality and reasonable price. Reliable quality and reasonable price are the basis of our continuous development.

Contact

Get in touch Please leave the questions you need to consult, later we will have a professional technical team to contact you.

Tel: +86 0577-28828932

WhatsApp/WeChat: +86 15658617888

© 2026 ZHONGYUE VALVE. All rights reserved.

QR code for Zhongyue Valve on WeChat
QR code for Zhongyue Valve on WeChat

WhatsApp

WeChat

QR code for Zhongyue Valve on WhatsApp
QR code for Zhongyue Valve on WhatsApp